Category: Fabs Lab

  • IK Multimedia – T-RackS- White 2A

    Hey Labfans! Have happy new month!

    Lets get into analysing the T-Racks white 2a today!

    If you are new to the lab posts ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    (Measurement settings above)

    FR

    fr Edit Content

    We can see some minimal FR content, there is no noise either. I would have expected a more intricate FR, but its not linear either.

    Phase

    phase Edit Content

    Phase is minimal aswell

    THD/THD+N
    (measured with input gain* steps)

    http   makeagif.com  media 9 02 2013 Jvbj6C Edit Content

    We can definitely see that the modeling is there, not sure about those harmonics before the fundamental though…

    Its quite a generous THD with quite rich character and a smoothness due to the increased even order harmonics. It also has an ‘bite’ feel on the lower steps.

    DSC

    DSC Edit Content

    Here we can see something quite interesting… The envelope knee  tends to a hard bend,  which is something  contrasting to the opto designs that are well known for their knee super softness. The operation though of the gain reduction in general is and can be considered subtle.

    DSC (limit)

    DSC%20limit Edit Content

    Well not much of a difference, almost none. My best bet is this might be a software bug.

     Q: If I don’t compress can I use this unit as a saturator ?

    A: Yes,definitely you can use this unit as a saturator, by increasing/decreasing the input gain knob to taste. but please be cautious and use a trim plugin after the 2a, lowering the overall gain before you start playing with the input gain.

    Consensus

    Well the modeling is there.

    Personal Quote: The downside for me is the knee hardness , making it really not an opto design. Ofcourse the way the reduction is implemented tends to ”compensate”  for the knee but well , but…

     

    None the less, the work is there!

     

    Fab

  • IK Multimedia – T-RackS- Black 76

    Hey Labfans! I hope you are having a good sunday!

    Today we will be analyzing T-RackS Black 76!

    If you are new to the lab posts ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    Measurement settings (above)

    FR

    FR Edit Content

    We can see that there is some minimal FR content. From a micro-scale analysis we can conclude that there is no noise modeling either. Right away we can expect some roughness in the DSC. (In  my opinion no noise is not a bad thing, 1176s have a high noise so bypassing it can be to our advantage)

    PS: This FR is shared with all ratios & ALL in mode

    Phase

    phase Edit Content

    Phase is also optimal

    THD/THD+N

    Lets look at THD with compression ON (measured in input steps)

    compON Edit Content

    Its there, this is a modeled THD, and a quite generous one! The distortion character is aggressive

    Lets look at THD with Compression OFF (measured with input steps)

    compoff Edit Content

    In this plot we can observe that the distortion has increased, a LOT! With this kind of extreme distortion the unit can be used for saturation. Due to this extreme distortion, we should also expect DSC to have some sort of compression curve, in the compressor off mode, yeap that’s right!

    Bellow is the ALL IN – THD – at max input.

    Personally I would expect way more THD  and different harmonic architecture for just the ALL IN mode.

    ALL Edit Content

    DSC

     DSC Edit Content

    Here we can observe the compressor envelope (In the 4:1) and the anticipated roughness, also it is good to notice that the envelope is somewhat between soft knee and hard knee.

    DSC – ALL IN

    DSC%20ALL Edit Content

    Here we can observe that the ALL IN mode envelope is more of a limiter than a compressor envelope.

    COMP OFF – DSC (max input)

    DSCOFFCOMP Edit Content

    Here we can see that the envelope is kind of like a compressor with a range option, compressing and then ‘expanding’  back to default.

    Ps: Yes, the GR meter is not showing you this, I am 🙂

    Caution: if you are going to use the unit as a saturator, always have the output lowered enough before you crank the input!

    Consensus

    Yes the Analogue modeling is there, intricate and Interesting!

     

     

    Personal Quote: In my opinion, a more intricate FR with little noise. along with  just a bit harder Knee and an ALL IN thats more agressive in THD would just come closer to the original 1176! 

    The work is there though! Enjoy it!

     

     

     

    Fab

  • Waves – API 550A + API 550B

    Hey Labfans! Today I will be analysing the 550 A/B from Waves.

    Lets get to it!

    Settings for the meassurment of 550A (Image Left)

    If you are new to the lab post ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    FR

    fr Edit Content

    Right away we can observe there is some minimal fr content, too minimal in my opinion.

    Noise was very low I had to use a micro-scale to identify it, but its there.

    Here is the plot

    noise Edit Content

    Phase

    phs Edit Content

    Phase is nominal

    Lets look how the FR looks with the FLTR .

    FLTR  FR

    fr%20fltr Edit Content

    Well we can clearly see a low/high pass response.

    FLTR  Phase

    phaser%20fltr Edit Content

    From the phase plot we can safely conclude that the highpass is between 6 and 12 dB/octave and the lowpass is less than 6 dB/octave.

    THD/THD+N

    THD Edit Content

    We can see that indeed there is THD content. It is not much but its not below either.

    One thing that is very interesting is the fundamental.There are no artifacts around it! Which is a rare occurrence in the digital ‘analogue model’ domain! Also along with that is the order formation! We can see that the THD content is limited up to the 5th order, quite unusual (in a good way) as well.

    API 550B

    Settings used for 550 B.

    phase%20 %20Copy Edit Content

     

    FR

    fr Edit Content

    We can see some FR content!

    Again I had to use a micro – scale to identify noise

    noise Edit Content

    Its really not that much, but its there.

    Phase

    phase Edit Content

    Phase is almost linear

    THD/THD+N

    Here is where it gets intresting…

    The first time I saw the 550 B THD, It kinda felt familiar and I overlayed it with the 550 A.

    They perfectly matched. I also conducted a more advanced measurement to confirm this.

    So I can confirm they both share the same THD.

    Below is the both 550 A/B THD overlayed to each other. Only the noise floor looks like its not overlapping but that is normal since the units have been overlayed periodically.

    OVERLAYED%20A%20B%20THD Edit Content

    (1.666% m/)

    Analogue switch: When the units analogue is turned off, THD is subtracted along with noise, Only FR remains as is.

     

     

    Consensus

    So the modeling is there, its less than I expected but more interesting that I anticipated. The only downside is the THD which is identical in both units.

     

    Q: Is this really modeled after API 550 and if so to what degree ?

    A:The only way to know,  is to cross reference data from the real API Module.

     PS1: In ‘analogue’ modeled EQ units bands behavior and characteristics are also modeled, but in order to evaluate this in this emulation, we would need the real source data.

     

    -If you enjoy my posts, please support me by sharing and liking the Lab!

     

     

    Fab

  • Slate Digital – VCC -Ψ

    Hey Labfans! Today I’ll be analyzing Slates Digital VCC Ψ! 

     

     

     

    Here are the settings utilized (No oversampling)(image left)

     If you are new to the lab post ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    FR

    fre Edit Content

    Right of the bat, again noise modeling! The Fr looks like this.

    Next is the fr from minimum Drive to Max Drive!

    FR DR

    fr Edit Content

    Now, thats an intricate FR!

    The more the drive the more the mid high/ high end boost & distortion. the less the ”cardboard” FR range  😉

    (And vice versa)

    Not even reached THD and half the modeling is here.

    Phase

    phase Edit Content

    Zoomed in plot – Here is the phase in max/min drive steps – looking good!

    THD/THD+N

     

    http   makeagif.com  media 8 24 2013 ERvaxl Edit Content

    Here we can observe the THD relationships with an input min to max, step to step measurement.

     Again,The result is a great example of how an analogue modeled THD should look like.

    This unit behavior is rich and aggressive! Even order harmonics are not in a descending order, still odd harmonics keep biting when they can! Also the basis of the distortion is lower than the 4k, but there’s an intricate fr  keeping us from figuring it out 😉 

    DSC

    DSC Edit Content

    Yeap, as anticipated based on the FR plot its like it should !

    Consensus

    This is once again the real deal, hands and feet down.

     

    Fab

  • Slate Digital – VCC -4K

    Slate Digital – VCC -4K

    Hey Labfans! Today I’ll be analyzing Slates Digital VCC 4k! 

     

     

     

    Here are the settings utilized (No oversampling) (image left)

    If you are new to the lab post ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    FR

    FR Edit Content

    Right away we can observe that there is noise modeling, other than that we can also observe that the FR is not that extreme, but its there. We can expect for DSC to be slightly rough right away. So before even getting too deep, half the modeling is here. It’s all about THD now!

    Phase

    phase Edit Content

     

    THD/THD+N

    http   makeagif.com  media 8 23 2013 qGKrR9 Edit Content

    Here we can observe the THD relationships with an input min to max, step to step measurement.

    The result is a great example of how an analogue modeled THD should look like.

    Q: So why this unit is considered an aggressive sound?

    A: As we can observe the odd order harmonics behavior is intricate, interchangeable and gradually rising. Odd order harmonics with this kind of behavior have an aggressive and in your face effect. Even order harmonics behave in a supportive manner helping the odd harmonics aggression stick out while aiding to the fullness of the distortion.

    PS: The interaction of the harmonics is far more complex! After all this is just a step to step GIF for demonstration purposes. Only a video capture would be able to capture a more detailed interaction.

    DSC

    DSC Edit Content

    Some roughness as anticipated already from the FR and this is of course normal for a summing emulation!

    Consensus

    This is the real deal, hands down.

     

    Fab

  • SOR 8 – Stressor

    SOR 8 – Stressor

    Hello Labfans! Today we will be analyzing the Stressor from SOR 8.

    This is not a commercial plugin but rather a freeware plugin, already accepting donations, with almost 150 thousand downloads, as the developer claims.

    Let me begin with two parts from the developer description of the plugin:

    As a special lab post today, I aspire to use one extra measurement aspect (The second listed below).

    1. We will conduct a generic analogue recreation evaluation, in the all common terms which are used in all posts until today.
    2. In order to be able to go into this aspect the previous generic recreation measurements must be validated as a success. This special aspect will be about evaluating each component to a ratio of similarity to the original EL – 8 Compressor data. We cannot expect a ‘copy’ like behavior since this is a ‘based’ plugin, but we can definitely expect some fundamental similarities, which can justify the ‘based’ upon claim of the developer.

    Let’s get to it! 🙂

    Measurement settings (image right)

    If you are new to the lab post ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    FR

    1fr Edit Content

    Here is the FR in the DIST 0 setting, as we can see there is a slight low shelf filter.

    Let’s look at the FR of DIST 1

    DIST 1 FR

    2fr Edit Content

    Here we can observe a gain increase in the previous low shelve plot. Let’s move to the last module DIST 2

    DIST 2 FR

    3fr Edit Content

    Here we can see the same low shelf  plot with quite drastic gain increase.

    Q: So is this some sort of analogue FR response?

    A: Long version: In order to evaluate this, we need to make a dynamic measurement, observe and create a low shelf trail for all the magnitude points in relation to compression, and then if all measurement points are identical this is just post DSC  digital static boost just like in a digital EQ.

    A:Short version: No

    Below you can see the results of this dynamic trail measurement that validates this. These characteristics applies in all DIST modes.

    MIN/MAX FR/GR – DIST 2 

    Steps Edit Content

    Blue = Min input (plugin), Green = Max Input/Comp (plugin)

    Phase

    p1 Edit Content

    DIST 0 phase is good

    p2 Edit Content

    DIST 1 phase also minimal

    p3 Edit Content

    DIST 2 is also minimal.

    THD/THD+N

    http   makeagif.com  media 8 19 2013 TkzbAl Edit Content

    Here we can observe the DIST 0 mode within a dynamic measurement of input steps.This has been done in order to evaluate if the harmonics that exists are compression Sid effects or actual analogue modeling, from the harmonic behavior we can safely ensure these are indeed compression Sid effects, which are typical for most digital compression/clip/limit  and cannot be associated with analogue modeling what so ever. In this case this is fairly obvious from the Klirr as well, but in order to be accurate we have to measure every aspect.

    Interesting Fact 1 + 2 = DIST modes 1 and 2 share this exact same behavior, with the sole difference of having an increased Klirr percentage.

    Ps: If you have read the Focusrite midnight compressor post already you should be familiar to this.

    DSC

    dsc Edit Content

    Interesting fact 1 +2: A low shelf FR that starts to rise in gain, and especially a static post DSC one as it is with DIST (1, 2), can create a false positive in DSC creating extreme  unnatural”roughness”, If I didn’t know any better I’d fallen for it, thankfully the DIST 0 does not exceed the threshold for this fallacy to occur and will not temper our DSC ,this provides us with the true  linear envelope – Dynamic response of the plugin.

     

     

     

    Consensus:

    This plugin has nothing to do with analogue modeling in any way, and therefor Distressor® EL-8 Compressor. Nor is or should be considered inspired, associated, or based by it.

    Therefore we cannot conduct our second aspect of measurements.

     

    Q: Where can I find a Distressor inspired/based emulation!?

    A: For a freeware you can check Antress plugins ‘Deathcore’’! For commercial, the discontinued Focusrite Liquid Mix has its own inspired/based model of the Distressor called ‘Copy Cat’. (I’ve tested both)

    For you that Antress isn’t compatible for your os/Daw, you have to work around adapters, it’s worth it 🙂

     

    -If you enjoy the Lab, and want to support me, please share the lab!

     

    Fab

     

     

  • Waves – CLA 2A [UPDATE]

    Waves – CLA 2A [UPDATE]

    Hey Labfans, this is the third time i’m starting to type this post, since the amazing chrome just likes to crash…..so: Waves CLA-2a

    Let me give you a point of whats up with the CLA series. Waves decided to model CLAs Compressors in order to capture their sonics & behavior, why would they do that ? , and not use any LA2a ?

    That is because in the analogue domain, two units that share the same production line, will never be identical they can be close but they can also be far apart! this creates a variety of different sonics & behaviors withing the same range. This fact has been abused by Producers for ages…

    Now lets get to it! (and hopefully chrome won’t crash again)

    Settings of messurments (image on top)

    If you are new to the lab post ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    FR

    fr Edit Content

    Right away we can see a high end attenuation that’s less than a dB…

    [update content]

    This is a new graph I have added, demonstrates the gain reduction interaction to the FR.

    FR:GR

    123dr2 Edit Content

    Top blue is no GR., bottom blue is extreme GR

    Phase

    phs Edit Content

    No phase issues.

    THD/THD+N

    thd Edit Content

    As we can see here the distortion is normal for a analogue modeling, the distortion character based on its behavior and harmonic orders can be considered Smooth & full.

    Q: Why didn’t you use the noise button ?

    A: Because not much will have changed in the way THD and FR are. Analogue has the noise sideeffect which is considered a bad thing. and is a bad thing. Aslong as we can abuse the digital system to turn off noise from any emulation this is to our advantage!

    DSC

    For DSC I used a higher gain reduction setting, to demonstrate the following.

    DSC Edit Content

    Here the compressor knee is very soft and gentle…

    Remember, DSC is strongly interconnected with FR. A near linear flat response would only most likely have the effect to make DSC near linear aswell. Wich is not the case here.

    Intresting Fact 1

    If we use the limit option, the knee just bends to a harder setting approaching closer to a contemporary compressor design. Bellow is how DSC looks in limit mode.

    DSC2 Edit Content

     

    Consensus

    This is a complete emulation model of analog.

     

    Q:  Is this really close to CLAs compressor ?

    A: I can’t know, get me to test CLAs unit and I’ll let you know.

     

    Hey and if want to support me, In making more reviews like & share 🙂

     

    Fab

  • Waves – SSL G-Master Bus Compressor

    Hey Lab fans! 🙂

    Today I’m gonna focus on the Waves ssl masterbuss comp, lets see!

     

    Settings used for the measurement(Image Left)

    If you are new to the lab post ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    FR

    fr Edit Content

    Right away we can observe that there is noise, that is why the fr looks like this, other than that its flat. This indicates that DSC will be linear aswell.

    phase Edit Content

    Well, no phase issues either…

    THD/THD+N

    http   makeagif.com  media 8 16 2013 wj5W p Edit Content

    Well this is a tough one, I can see the analogue modeling and I can verify it, but the ratio at which it exists its a bit low, so I verify that it is there, but I also verify that its not as much as I’d expect.

    The Character of the THD is aggressive and a bit smooth & rich. That is due to the 3rd order harmonic that is constantly almost stable, but also because 2nd order harmonics exist aswell but they are less stable and in a lower amplitude.

    Interesting Fact 1:

    The analog button in the GUI, just adds noise. When you’d expect to subtract the distortion as well .Here is the THD without the analogue button, the only thing that changed is that there is no noisefloor.

    0 Edit Content

    DSC

    dsc Edit Content

    Is bound to be linear

     

    Intresting fact 2 : The knee becomes hard only in the ratio of 10

     

    Consensus

    So what can I say, I expected more distortion (specialy for this kind of unit)  but the modeling is there. The response is linear and the envelope is bound to be aswell, and the analogue button just adds noise…

    So basically this is a ”partially” modeled plugin. It has the soul, but it lacks the heart (FR).

     

    Q: Could you do a VS thread with other products that emulate this ?

    A: Its gonna happen after the individual products are analyzed and reviewed.

     

    If you want more Fab labs, Please share the lab!

     

    Fab.

  • SSL DUENDE – Stereo Buss Compressor

    Today lets see whats up with the ssl modeling!

     

    Here are the settings used for the analysis(Image Left)

     If you are new to the lab post ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    FR

    http   makeagif.com  media 8 16 2013 bDNkun Edit Content

    Woot !? well to begin with, the response is flat, but when you dial the attack from 0.1 to 30 this phenomenon occurs (blue is for right and yellow for left), in other words. When the compression goes up the two channels create more difference in magnitude from eachother, one being slightly louder than the other following in a symmetrical pattern. This is indeed quite odd… I’m not sure if this is something you would want for you masterbuss. None the less I have to note that the increase has a limit being the lowest value you see in this animated graph. What this means is no matter how much compression you dial the magnitude difference will not get any bigger, but when you dial down from a certain point the difference will begin to degrease.

    ps: Theres no noise modeling either (that’s not always a bad thing)

    Phase

    flat Edit Content

    Flat, nothing to see here …

    THD/THD+N

    http   makeagif.com  media 8 16 2013 5vrHF6 Edit Content

    Here we can see the THD unit behavior from -20 Threshold, to +20.

    By observing the THD behavior, we can safely conclude that this is Analogue Distortion modeling. Based on how the order of harmonics is and behaves this gives the unit an  agressive character because the only harmonics present are the 3rd order and its multyplicates, which is a common behavior of transistor units (but not exclusively).

    DSC

    DSC41 Edit Content

     I was expecting that the moment I saw the FR since they are interlinked. 

    Interesting fact 1: this might not be so relevant, but I had to share it. Look what happens when y zoom into the bend curve.

    dsczoomed Edit Content

    (this happens only in the bended part) Usualy this is totaly flat,  As we see here its like micro tiny compressors are dialed for each step, pretty odd and cool !?

    Interesting Fact 2:

    If you dial a ratio of 2 the compressor envelope is opto like, all other settings have a hard knee.

    Compressor dialed with the ratio of 2

    adwa3wda Edit Content

     

    My Consensus

    Well, this compressor has an odd behavior that’s fact, other than that it feels to me like they modeled the soul and left the body (FR). In other words this is ”partially” modeled.

     

    Fab

  • Focusrite – Midnight Compressor

    Again I will start with.. 

    ” Focusrite’s new Midnight plug-in suite takes two of the most iconic Focusrite modules of all time – the ISA110 equaliser and ISA130 compressor; models their sound exactly with powerful DSP technology; and gives them elegant, functional on-screen front panels that make them simplicity itself to use. Now you can add that authentic, classic Focusrite sound to your own tracks at a price you can afford. Your productions have never sounded so good.”

    Settings used for the measurements Above

    If you are new to the lab post ,read this https://www.gearevu.littlefishaudio.com/must-read-welcome-to-my-lab-updated/

    FR

    fc1 Edit Content

     

    Well Flat, the only downside was that the makeup gain steps just wouldn’t fine align that’s why it’s slightly below, right away the DSC will be linear aswell.

     

    Phase

    fc2 Edit Content

    Flat

    THD/THD+N

    fc3 Edit Content

    Alright let me give you some basic understanding of what you see, you either see a modeled THD which is so low you can’t even consider it THD, or harmonics created by only the compression which is a ”natural” phenomenon … I could have just ruled this THD off because of its Klirr, but instead I will proceed, in order to educate in something new.

    Q: OMG do you mean digital can sound analogue by itself, because compressing digitally can create harmonics? And this is what we are looking for in this graph right? :O

    A: No because here is what happens, Harmonics/Harmonic Distortion created by hard/soft clipping and compression are static in almost all level values, unlike analogue which has a very defined value for  each magnitude that interacts altogether. Digital has a static form in almost all magnitude points.

    So is this a modeled THD or just a Compression Sideffect?

    In order to be able to find this out, we need to create a dynamic test in the next test you can see the interaction of the THD from -18dB to +18dB

    jYMhsf Edit Content

    Yeap, this comfirms my suspicion, this is digital compression sideffects. In other words no analogue modeling THD.

     

     

    Consensus

    This is a digital Softknee Compressor

     

     

    Fab