Brand: Avantone

  • Avantone Active MixCube Pair –  (Red) Demo Unit

    Avantone Active MixCube Pair – (Red) Demo Unit

    Avantone Active MixCubes Powered Full-Range Mini Reference Monitors DEMO Unit

    The Avantone MixCubes are shielded, full-range mini reference monitors. Their design is inspired by the legacy of the 5C Sound Cubes used in virtually all-major studios for the last 25 years.

    Application
    Active Recording / Mixdown Monitors

    Engineering Objective
    The Avantone Active Mixcubes are designed to be high-resolution, full-range powered mini-reference monitors for fixed or remote locations.
    The secondary engineering facet was to create a timeless design that compliments a single full-range transducer.

    Performance Objective
    Studios primarily use 2-way & 3-way larger monitors designed to represent a wide range reference viewpoint at higher listening levels. However, in this newly developing age of High Definition Audio, there is still a need to also hear what your mix will sound like when played back over small “bass-challenged” systems such as televisions, clock radios, computers, car stereos, iPod docking stations, etc. It is important to make mixing judgments based partially on listening to reference monitors that will not impart tonal anomalies caused by crossovers or inferior full range drivers. Particular attention is always paid to the critical mid-range vocal/guitar/keyboard areas. This is where having a full-range monitor without a crossover is truly revealing. Ten months of R&D comparative listening & tweaking went into the voicing of the AVANTONE MixCubes. The result is a very smooth sounding, full range upgrade from the original 5C Sound Cubes. Listening tests reveal that the MixCubes have a smooth, more open, transparent top end response with extended bass while maintaining their basic original character.

    Cabinet Design
    The original 5C Sound Cubes™ were made of ½” particleboard covered with a glue-on wood grain contact paper. We chose to use thicker, denser MDF board because of its high rigidity and inherent low-resonance characteristics. We started with a 165mm (6 1/2″) sealed cube design with radiused edges. We then chose an elegant Polyurethane high gloss “RETRO-CREAM” finish. The originals had either screws or on later models plastic binding posts mounted on a recessed plastic cup. We upgraded to high-end nickel plated, machined solid metal binding posts (Dual banana spacing) mounted on a black anodized ,milled and silk-screened aluminum terminal plate. Next we added a 7mm thick neoprene pad embedded into the base of the cabinet to serve as a skid-resistant acoustic isolator. Additionally, for creative mounting situations, we recessed an industry standard 5/8”-27 mic stand mount into the base.

    Driver Design
    The originals were a basic 5” stamped frame design. We designed a proprietary 5.25” die cast aluminum frame driver/cone assembly to exceed the performance of the originals. The mounting bezel is then polished for an elegant appearance. The paper cone, chosen for its musical character, is custom designed & crafted using the finest New Zealand pulp with mica fibers added for lighter weight & rigidity. The cloth surround is made in Japan to exacting uniform thickness tolerances. The Top Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel enabling the highest modeled flux density in the gap. The magnets are Y- 40 GRADE (MIL-SPEC) yielding a 43oz. High Power-low distortion motor structure.

    Amplifier Design
    We designed the amp module from the ground up to be a true professional-grade amplifier. It incorporates “overkill” concepts in component selection as well as safety. The result is a “no-compromise” amp with robust headroom characteristics that will rival the performance of much higher priced studio rack mount amps.

  • Avantone Active MixCube Pair –  Butter Cream

    Avantone Active MixCube Pair – Butter Cream

    Avantone Active MixCubes Powered Full-Range Mini Reference Monitors

    The Avantone MixCubes are shielded, full-range mini reference monitors. Their design is inspired by the legacy of the 5C Sound Cubes used in virtually all-major studios for the last 25 years.

    Application
    Active Recording / Mixdown Monitors

    Engineering Objective
    The Avantone Active Mixcubes are designed to be high-resolution, full-range powered mini-reference monitors for fixed or remote locations.
    The secondary engineering facet was to create a timeless design that compliments a single full-range transducer.

    Performance Objective
    Studios primarily use 2-way & 3-way larger monitors designed to represent a wide range reference viewpoint at higher listening levels. However, in this newly developing age of High Definition Audio, there is still a need to also hear what your mix will sound like when played back over small “bass-challenged” systems such as televisions, clock radios, computers, car stereos, iPod docking stations, etc. It is important to make mixing judgments based partially on listening to reference monitors that will not impart tonal anomalies caused by crossovers or inferior full range drivers. Particular attention is always paid to the critical mid-range vocal/guitar/keyboard areas. This is where having a full-range monitor without a crossover is truly revealing. Ten months of R&D comparative listening & tweaking went into the voicing of the AVANTONE MixCubes. The result is a very smooth sounding, full range upgrade from the original 5C Sound Cubes. Listening tests reveal that the MixCubes have a smooth, more open, transparent top end response with extended bass while maintaining their basic original character.

    Cabinet Design
    The original 5C Sound Cubes™ were made of ½” particleboard covered with a glue-on wood grain contact paper. We chose to use thicker, denser MDF board because of its high rigidity and inherent low-resonance characteristics. We started with a 165mm (6 1/2″) sealed cube design with radiused edges. We then chose an elegant Polyurethane high gloss “RETRO-CREAM” finish. The originals had either screws or on later models plastic binding posts mounted on a recessed plastic cup. We upgraded to high-end nickel plated, machined solid metal binding posts (Dual banana spacing) mounted on a black anodized ,milled and silk-screened aluminum terminal plate. Next we added a 7mm thick neoprene pad embedded into the base of the cabinet to serve as a skid-resistant acoustic isolator. Additionally, for creative mounting situations, we recessed an industry standard 5/8”-27 mic stand mount into the base.

    Driver Design
    The originals were a basic 5” stamped frame design. We designed a proprietary 5.25” die cast aluminum frame driver/cone assembly to exceed the performance of the originals. The mounting bezel is then polished for an elegant appearance. The paper cone, chosen for its musical character, is custom designed & crafted using the finest New Zealand pulp with mica fibers added for lighter weight & rigidity. The cloth surround is made in Japan to exacting uniform thickness tolerances. The Top Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel enabling the highest modeled flux density in the gap. The magnets are Y- 40 GRADE (MIL-SPEC) yielding a 43oz. High Power-low distortion motor structure.

    Amplifier Design
    We designed the amp module from the ground up to be a true professional-grade amplifier. It incorporates “overkill” concepts in component selection as well as safety. The result is a “no-compromise” amp with robust headroom characteristics that will rival the performance of much higher priced studio rack mount amps.

  • Avantone Active MixCube Pair –  Butter Cream Demo Unit

    Avantone Active MixCube Pair – Butter Cream Demo Unit

    Avantone Active MixCubes Powered Full-Range Mini Reference Monitors “Demo Unit”

    The Avantone MixCubes are shielded, full-range mini reference monitors. Their design is inspired by the legacy of the 5C Sound Cubes used in virtually all-major studios for the last 25 years.

    Application
    Active Recording / Mixdown Monitors

    Engineering Objective
    The Avantone Active Mixcubes are designed to be high-resolution, full-range powered mini-reference monitors for fixed or remote locations.
    The secondary engineering facet was to create a timeless design that compliments a single full-range transducer.

    Performance Objective
    Studios primarily use 2-way & 3-way larger monitors designed to represent a wide range reference viewpoint at higher listening levels. However, in this newly developing age of High Definition Audio, there is still a need to also hear what your mix will sound like when played back over small “bass-challenged” systems such as televisions, clock radios, computers, car stereos, iPod docking stations, etc. It is important to make mixing judgments based partially on listening to reference monitors that will not impart tonal anomalies caused by crossovers or inferior full range drivers. Particular attention is always paid to the critical mid-range vocal/guitar/keyboard areas. This is where having a full-range monitor without a crossover is truly revealing. Ten months of R&D comparative listening & tweaking went into the voicing of the AVANTONE MixCubes. The result is a very smooth sounding, full range upgrade from the original 5C Sound Cubes. Listening tests reveal that the MixCubes have a smooth, more open, transparent top end response with extended bass while maintaining their basic original character.

    Cabinet Design
    The original 5C Sound Cubes™ were made of ½” particleboard covered with a glue-on wood grain contact paper. We chose to use thicker, denser MDF board because of its high rigidity and inherent low-resonance characteristics. We started with a 165mm (6 1/2″) sealed cube design with radiused edges. We then chose an elegant Polyurethane high gloss “RETRO-CREAM” finish. The originals had either screws or on later models plastic binding posts mounted on a recessed plastic cup. We upgraded to high-end nickel plated, machined solid metal binding posts (Dual banana spacing) mounted on a black anodized ,milled and silk-screened aluminum terminal plate. Next we added a 7mm thick neoprene pad embedded into the base of the cabinet to serve as a skid-resistant acoustic isolator. Additionally, for creative mounting situations, we recessed an industry standard 5/8”-27 mic stand mount into the base.

    Driver Design
    The originals were a basic 5” stamped frame design. We designed a proprietary 5.25” die cast aluminum frame driver/cone assembly to exceed the performance of the originals. The mounting bezel is then polished for an elegant appearance. The paper cone, chosen for its musical character, is custom designed & crafted using the finest New Zealand pulp with mica fibers added for lighter weight & rigidity. The cloth surround is made in Japan to exacting uniform thickness tolerances. The Top Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel enabling the highest modeled flux density in the gap. The magnets are Y- 40 GRADE (MIL-SPEC) yielding a 43oz. High Power-low distortion motor structure.

    Amplifier Design
    We designed the amp module from the ground up to be a true professional-grade amplifier. It incorporates “overkill” concepts in component selection as well as safety. The result is a “no-compromise” amp with robust headroom characteristics that will rival the performance of much higher priced studio rack mount amps.

  • Avantone Active MixCube Pair – Black

    Avantone Active MixCube Pair – Black

    Avantone Active MixCubes Powered Full-Range Mini Reference Monitors in Limited Edition Black

    The Avantone MixCubes are shielded, full-range mini reference monitors. Their design is inspired by the legacy of the 5C Sound Cubes used in virtually all-major studios for the last 25 years.

    Application
    Active Recording / Mixdown Monitors

    Engineering Objective
    The Avantone Active Mixcubes are designed to be high-resolution, full-range powered mini-reference monitors for fixed or remote locations.
    The secondary engineering facet was to create a timeless design that compliments a single full-range transducer.

    Performance Objective
    Studios primarily use 2-way & 3-way larger monitors designed to represent a wide range reference viewpoint at higher listening levels. However, in this newly developing age of High Definition Audio, there is still a need to also hear what your mix will sound like when played back over small “bass-challenged” systems such as televisions, clock radios, computers, car stereos, iPod docking stations, etc. It is important to make mixing judgments based partially on listening to reference monitors that will not impart tonal anomalies caused by crossovers or inferior full range drivers. Particular attention is always paid to the critical mid-range vocal/guitar/keyboard areas. This is where having a full-range monitor without a crossover is truly revealing. Ten months of R&D comparative listening & tweaking went into the voicing of the AVANTONE MixCubes. The result is a very smooth sounding, full range upgrade from the original 5C Sound Cubes. Listening tests reveal that the MixCubes have a smooth, more open, transparent top end response with extended bass while maintaining their basic original character.

    Cabinet Design
    The original 5C Sound Cubes™ were made of ½” particleboard covered with a glue-on wood grain contact paper. We chose to use thicker, denser MDF board because of its high rigidity and inherent low-resonance characteristics. We started with a 165mm (6 1/2″) sealed cube design with radiused edges. We then chose an elegant Polyurethane high gloss “RETRO-CREAM” finish. The originals had either screws or on later models plastic binding posts mounted on a recessed plastic cup. We upgraded to high-end nickel plated, machined solid metal binding posts (Dual banana spacing) mounted on a black anodized ,milled and silk-screened aluminum terminal plate. Next we added a 7mm thick neoprene pad embedded into the base of the cabinet to serve as a skid-resistant acoustic isolator. Additionally, for creative mounting situations, we recessed an industry standard 5/8”-27 mic stand mount into the base.

    Driver Design
    The originals were a basic 5” stamped frame design. We designed a proprietary 5.25” die cast aluminum frame driver/cone assembly to exceed the performance of the originals. The mounting bezel is then polished for an elegant appearance. The paper cone, chosen for its musical character, is custom designed & crafted using the finest New Zealand pulp with mica fibers added for lighter weight & rigidity. The cloth surround is made in Japan to exacting uniform thickness tolerances. The Top Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel enabling the highest modeled flux density in the gap. The magnets are Y- 40 GRADE (MIL-SPEC) yielding a 43oz. High Power-low distortion motor structure.

    Amplifier Design
    We designed the amp module from the ground up to be a true professional-grade amplifier. It incorporates “overkill” concepts in component selection as well as safety. The result is a “no-compromise” amp with robust headroom characteristics that will rival the performance of much higher priced studio rack mount amps.

  • Avantone CDMK-7 7-Piece Drum Mics Kit

    Avantone CDMK-7 7-Piece Drum Mics Kit

     Avantone CDMK-7 7-Mic Drum Mics KitAvantone CDMK7 7 Mic Drum Microphone Kit

    Avantone CDMK-7 7-Mic Drum Mics Kit

    These are the 2nd generation of drum mics from Avantone and a great deal of R&D effort has culminated in these rugged, great sounding drum mics. We feel they represent the very finest drum microphone packages available, both for live clubs & concerts, as well as serious studio recording projects. The Avantone CDMK drum mics are truly gorgeous looking and sounding microphones. Their proprietary design, character and performance are made to set a new standard in drum mic’ing.

    A unique feature of all our dynamic drum mics in the Avantone CDMK series is a pair of machined insets on the barrel of each microphone body. These insets allow the O-rings of the SSM shockmount to “lock” the mic into place, which prevents mic shifting and slippage. Aesthetically, each mic features an elegant Cabernet Wine-Red finish, accented with polished nickel trim. Any studio or venue can proudly & confidently offer the CDMK drum mic kit for professional use.

    All components are designed and manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability.

    Mics / Accessories included

    • (1) Mondo Kick Drum Mic
    • (1) ADM Snare Drum Mic
    • (3) ATOM Tome Mics
    • (2) CK-1 Cardioid Condenser Mics
    • (4) PK-1 Pro-Klamp Drum Rim Mic Mounts
    • (7) SSM Metal Shockmounts

     

    The MONDO kick drum mic is the heart of the Avantone CDMK drum mic lineup. It offers a very aggressive frequency contour that sounds huge right out of the box, so most engineers will find little need for EQ… plus as in all our mics NO PLASTIC to break! The MONDO has a die-cast zinc body with a steel and brass grill assembly, and features internal shockmounting on the capsule assembly to prevent the transmission of unwanted “rumble” from physical vibrations.

    The ADM snare drum mic is voiced to “follow” the familiar sound of industry standard snare mics. However, we engineered a better low end and smoother, extended top end. The ADM has a die-cast zinc body with a steel and brass grill assembly. Although we call it a “snare drum mic”, the ADM is a versatile mic that is completely at home on high toms, bongos, congas, guitar cabinets, etc.

    The ATOM tom mic adheres to our overall tonal philosophy of “big sounding drums” and incorporates an oversize capsule that captures a huge low end as well as a penetrating attack. The ATOM is custom voiced to yield a fat, big sound that often requires no EQ at all! Because of the special voicing on the ATOM, it also is fantastic on djembe, large congas, and bass amp cabinets. Like our MONDO kick drum mic, the ATOM has a die-cast zinc body with a steel and brass grill assembly, and features internal shockmounting on the capsule assembly to prevent the transmission of unwanted “rumble” from physical vibrations.

    The CK-1 true condenser mics are utilized for overheads. The mics feature cardioid capsules for accurate stereo image capturing. Each CK-1 has a low frequency cutoff switch and 10dB attenuation switch for versatile tone shaping & signal control. It accurately captures the delicate nuances of the cymbals while rejecting sounds from interfering sources away from the kit. Each CK-1 microphone body and capsule assembly is precision machined from brass. The CK-1 in its normal stock version uses high grade Polystyrene and Metalized Polypropylene capacitors in the audio path. This represents our commitment to quality as these normally are the type of “upgrade” components that are implemented by microphone modder/hot-rodders!

    The PK-1 PRO-KLAMP drum rim mic mounts are superb in allowing a confident positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic with three(!) stages of rubber dampening/decoupling material. This isolation allows for professional results without the need for tripod/boom stands. While it was designed to withstand the rigors of live stage gigging, it is the first drum rim mic mount that will reliably work in a pro-studio situation. This makes the engineers’ job easier and insures that the mics will stay in place where he positions them. Each PK-1 is built for reliability and is exceptionally rugged, with heavy-duty metal construction.

    The SSM shock mounts are as rugged as you can find and allow for a superb decoupling of the mics from unwanted low-frequency transfer and rumble. This feature, coupled with the use of the PRO-KLAMPS, results in a much tighter, less muddy sound than other brands of drum mic kits. The O-rings are manufactured using a custom formula. The new world class Ethylene Propylene formula provides enormous resistance to breakage, resistance to surface nicks and remains supple and effective even against dry, hot temperatures. It has the best resistance to ozone and weathering, which makes it great for use around electronics devices, and maintains its physical properties even in a stretched condition. Each SSM is constructed of heavy-duty die-cast zinc, which is not only incredibly durable but also adds mass, which contributes to vibration dampening/decoupling.

    The custom vintage tweed case is hand-built for heavy-duty storage (and groovy-looking, to boot!). The metal corners, locking latches, high-density foam tray, and plush lining make this case very roadworthy while offering a visually unique design. Aesthetically, the case features a tweed and faux-alligator trim exterior, with a Cabernet wine-red plush lining. The slotted foam tray not only protects and stores each component of the drum mic kit, but also lifts out of the case to provide storage for cables, sticks, etc. Additionally, by removing the tray you are left with a fantastic and stylish piece of carry-on luggage.

    Specifications

      MONDO Kick Mic ADM Snare Mic ATOM Tom Mic CK-1 FET Mic
    Type Dynamic Dynamic Dynamic True Condenser
    Polar Pattern(s) Cardioid Cardioid Cardioid Cardioid
    Frequency Response 20Hz – 15kHz 50Hz – 16kHz 30Hz – 15kHz 30Hz – 20kHz +/- 3dB
    Output Impedance 210 Ohms 520 Ohms 220 Ohms 200 Ohms
    Maximum SPL 145dB 145dB 145dB 138dB (0.5% THD @1000Hz)
    Output Connector Male XLR 3-pin Male XLR 3-pin Male XLR 3-pin Male XLR 3-pin
    Power Requirements N/A N/A N/A Standard 48v phantom
    Weight .5 kg (16 oz) .35 kg (11 oz) .4 kg (13 oz) .16 kg (5 oz)
    Finish Cabernet / Black / Nickel Cabernet / Black / Nickel Cabernet / Black / Nickel Cabernet / Nickel
  • Avantone CDMK-8 8-Piece Drum Mics Kit

    Avantone CDMK-8 8-Piece Drum Mics Kit

    Avantone CDMK-8 8-Mic Drum Mics Kit

    These are the 2nd generation of drum mics from Avantone and a great deal of R&D effort has culminated in these rugged, great sounding drum mics. We feel they represent the very finest drum microphone packages available, both for live clubs & concerts, as well as serious studio recording projects.

    The Avantone CDMK drum mics are truly gorgeous looking and sounding microphones. Their proprietary design, character and performance are made to set a new standard in drum mic’ing.

    A unique feature of all our dynamic drum mics in the Avantone CDMK series is a pair of machined insets on the barrel of each microphone body. These insets allow the O-rings of the SSM shockmount to “lock” the mic into place, which prevents mic shifting and slippage.

    Aesthetically, each mic features an elegant Cabernet Wine-Red finish, accented with polished nickel trim. Any studio or venue can proudly & confidently offer the CDMK drum mic kit for professional use. All components are designed and manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability.

    Included Items:

    • (1) Mondo Kick Drum Microphone
    • (1) ADM Snare Drum Microphone
    • (3) ATOM Tom Microphones
    • (2) CK-1 Cardioid Condenser Mics (for overheads)
    • (1) CK-1 Hyper-cardioid Condenser Mic (for hi-hat)
    • (4) PK-1 Pro-Klamp Drum Rim Microphone Mounts
    • (8) SSM Metal Shockmounts
    • Custom Heavy Duty Locking Padded Tweed Vintage Case
    • Owner’s Manual

     

    The MONDO kick drum mic is the heart of the Avantone CDMK drum mic lineup. It offers a very aggressive frequency contour that sounds huge right out of the box, so most engineers will find little need for EQ… plus as in all our mics NO PLASTIC to break! The MONDO has a die-cast zinc body with a steel and brass grill assembly, and features internal shockmounting on the capsule assembly to prevent the transmission of unwanted “rumble” from physical vibrations.

    The ADM snare drum mic is voiced to “follow” the familiar sound of industry standard snare mics. However, we engineered a better low end and smoother, extended top end. The ADM has a die-cast zinc body with a steel and brass grill assembly. Although we call it a “snare drum mic”, the ADM is a versatile mic that is completely at home on high toms, bongos, congas, guitar cabinets, etc.

    The ATOM tom mic adheres to our overall tonal philosophy of “big sounding drums” and incorporates an oversize capsule that captures a huge low end as well as a penetrating attack. The ATOM is custom voiced to yield a fat, big sound that often requires no EQ at all! Because of the special voicing on the ATOM, it also is fantastic on djembe, large congas, and bass amp cabinets. Like our MONDO kick drum mic, the ATOM has a die-cast zinc body with a steel and brass grill assembly, and features internal shockmounting on the capsule assembly to prevent the transmission of unwanted “rumble” from physical vibrations.

    The CK-1 true condenser mics are utilized for overheads and hi-hat. The overheads feature cardioid capsules for accurate stereo image capturing, and the hi-hat mic utilizes a hyper-cardioid capsule to minimize bleed from adjacent drums. Each CK-1 has a low frequency cutoff switch and -10dB attenuation switch for versatile tone shaping & signal control. It accurately captures the delicate nuances of the cymbals while rejecting sounds from interfering sources away from the kit. Each CK-1 microphone body and capsule assembly is precision machined from brass. The CK-1 in its normal stock version uses high grade Polystyrene and Metalized Polypropylene capacitors in the audio path. This represents our commitment to quality as these normally are the type of “upgrade” components that are implemented by microphone modder/hot-rodders!

    The PK-1 PRO-KLAMP drum rim mic mounts are superb in allowing a confident positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic with three(!) stages of rubber dampening/decoupling material. This isolation allows for professional results without the need for tripod/boom stands. While it was designed to withstand the rigors of live stage gigging, it is the first drum rim mic mount that will reliably work in a pro-studio situation. This makes the engineers’ job easier and insures that the mics will stay in place where he positions them. Each PK-1 is built for reliability and is exceptionally rugged, with heavy-duty metal construction.

    The SSM shock mounts are as rugged as you can find and allow for a superb decoupling of the mics from unwanted low-frequency transfer and rumble. This feature, coupled with the use of the PRO-KLAMPS, results in a much tighter, less muddy sound than other brands of drum mic kits. The O-rings are manufactured using a custom formula. The new world class Ethylene Propylene formula provides enormous resistance to breakage, resistance to surface nicks and remains supple and effective even against dry, hot temperatures. It has the best resistance to ozone and weathering, which makes it great for use around electronics devices, and maintains its physical properties even in a stretched condition. Each SSM is constructed of heavy-duty die-cast zinc, which is not only incredibly durable but also adds mass, which contributes to vibration dampening/decoupling.

    The custom vintage tweed case is hand-built for heavy-duty storage (and groovy-looking, to boot!). The metal corners, locking latches, high-density foam tray, and plush lining make this case very roadworthy while offering a visually unique design. Aesthetically, the case features a tweed and faux-alligator trim exterior, with a Cabernet wine-red plush lining. The slotted foam tray not only protects and stores each component of the drum mic kit, but also lifts out of the case to provide storage for cables, sticks, etc. Additionally, by removing the tray you are left with a fantastic and stylish piece of carry-on luggage.

     

    Specifications

    MONDO Kick Mic

    • Type: Dynamic
    • Polar Pattern(s): Cardioid
    • Frequency Response: 20Hz – 15kHz
    • Output Impedance: 210 Ohms
    • Maximum SPL: 145dB
    • Output Connector: Male XLR 3 pin
    • Power Requirement: None
    • Weight: 0.5kg (16oz)
    • Finish: Cabernet / Black / Nickel

    ADM Snare Mic

    • Type: Dynamic
    • Polar Pattern(s): Cardioid
    • Frequency Response: 50Hz – 16kHz
    • Output Impedance: 520 Ohms
    • Maximum SPL: 145dB
    • Output Connector: Male XLR 3 pin
    • Power Requirement: None
    • Weight: 0.35kg (11oz)
    • Finish: Cabernet / Black / Nickel

    ATOM Tom Mic

    • Type: Dynamic
    • Polar Pattern(s): Cardioid
    • Frequency Response: 30Hz – 15kHz
    • Output Impedance: 220 Ohms
    • Maximum SPL: 145dB
    • Output Connector: Male XLR 3 pin
    • Power Requirement: None
    • Weight: 0.4kg (13oz)
    • Finish: Cabernet / Black / Nickel

    CK-1 FET Mic

    • Type: True Condenser
    • Polar Pattern(s): Cardioid & Hyper-Cardioid
    • Frequency Response: 30Hz – 15kHz
    • Output Impedance: 200 Ohms
    • Maximum SPL: 138dB (0.5% THD@1000Hz)
    • Output Connector: Male XLR 3 pin
    • Power Requirement: Standard 48v phantom
    • Weight: 0.16kg (5oz)
    • Finish: Cabernet / Nickel
  • Avantone CDMK4 4-Piece Drum Microphone Kit

    Avantone CDMK4 4-Piece Drum Microphone Kit

    Avantone CDMK-4 4-Mic Drum Mics KitAvantone CDMK4 4-Mic Drum Microphone Kit

    Avantone CDMK-4 4-Mic Drum Mics Kit

    These are the 2nd generation of drum mics from Avantone and a great deal of R&D effort has culminated in these rugged, great sounding drum mics. We feel they represent the very finest drum microphone packages available, both for live clubs & concerts, as well as serious studio recording projects.

    The Avantone CDMK drum mics are truly gorgeous looking and sounding microphones. Their proprietary design, character and performance are made to set a new standard in drum mic’ing. A unique feature of all our dynamic drum mics in the Avantone CDMK series is a pair of machined insets on the barrel of each microphone body. These insets allow the O-rings of the SSM shockmount to “lock” the mic into place, which prevents mic shifting and slippage.

    Aesthetically, each mic features an elegant Cabernet Wine-Red finish, accented with polished nickel trim. Any studio or venue can proudly & confidently offer the CDMK drum mic kit for professional use. All components are designed and manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability.

    Included Items

    • (1) Mondo Kick Drum Microphone
    • (1) ADM Snare Drum Microphone
    • (2) ATOM Tom Microphones
    • (3) PK-1 Pro-Klamp Drum Rim Microphone Mounts
    • (4) SSM Metal Shockmounts
    • Custom Heavy Duty Locking Padded Tweed Vintage Case
    • Owner’s Manual

    The MONDO kick drum mic is the heart of the Avantone CDMK drum mic lineup. It offers a very aggressive frequency contour that sounds huge right out of the box, so most engineers will find little need for EQ. . plus as in all our mics NO PLASTIC to break! The MONDO has a die-cast zinc body with a steel and brass grill assembly, and features internal shockmounting on the capsule assembly to prevent the transmission of unwanted “rumble” from physical vibrations.

    The ADM snare drum mic is voiced to “follow” the familiar sound of industry standard snare mics. However, we engineered a better low end and smoother, extended top end. The ADM has a die-cast zinc body with a steel and brass grill assembly. Although we call it a “snare drum mic”, the ADM is a versatile mic that is completely at home on high toms, bongos, congas, guitar cabinets, etc.

    The ATOM tom mic adheres to our overall tonal philosophy of “big sounding drums” and incorporates an oversize capsule that captures a huge low end as well as a penetrating attack. The ATOM is custom voiced to yield a fat, big sound that often requires no EQ at all! Because of the special voicing on the ATOM, it also is fantastic on djembe, large congas, and bass amp cabinets. Like our MONDO kick drum mic, the ATOM has a die-cast zinc body with a steel and brass grill assembly, and features internal shockmounting on the capsule assembly to prevent the transmission of unwanted “rumble” from physical vibrations.

    The PK-1 PRO-KLAMP drum rim mic mounts are superb in allowing a confident positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic with three(!) stages of rubber dampening/decoupling material. This isolation allows for professional results without the need for tripod/boom stands. While it was designed to withstand the rigors of live stage gigging, it is the first drum rim mic mount that will reliably work in a pro-studio situation. This makes the engineers’ job easier and insures that the mics will stay in place where he positions them. Each PK-1 is built for reliability and is exceptionally rugged, with heavy-duty metal construction.

    The SSM shock mounts are as rugged as you can find and allow for a superb decoupling of the mics from unwanted low-frequency transfer and rumble. This feature, coupled with the use of the PRO-KLAMPS, results in a much tighter, less muddy sound than other brands of drum mic kits. The O-rings are manufactured using a custom formula. The new world class Ethylene Propylene formula provides enormous resistance to breakage, resistance to surface nicks and remains supple and effective even against dry, hot temperatures. It has the best resistance to ozone and weathering, which makes it great for use around electronics devices, and maintains its physical properties even in a stretched condition. Each SSM is constructed of heavy-duty die-cast zinc, which is not only incredibly durable but also adds mass, which contributes to vibration dampening/decoupling.

    The custom vintage tweed case is hand-built for heavy-duty storage (and groovy-looking, to boot!). The metal corners, locking latches, high-density foam tray, and plush lining make this case very roadworthy while offering a visually unique design. Aesthetically, the case features a tweed and faux-alligator trim exterior, with a Cabernet wine-red plush lining. The slotted foam tray not only protects and stores each component of the drum mic kit, but also lifts out of the case to provide storage for cables, sticks, etc. Additionally, by removing the tray you are left with a fantastic and stylish piece of carry-on luggage.

     
     

     

    Specifications

    MONDO Kick Mic ADM Snare Mic ATOM Tom Mic
    Type Dynamic Dynamic Dynamic
    Polar Pattern(s) Cardioid Cardioid Cardioid
    Frequency Response 20Hz – 15kHz 50Hz – 16kHz 30Hz – 15kHz
    Output Impedance 210 Ohms 520 Ohms 220 Ohms
    Maximum SPL 145dB 145dB 145dB
    Output Connector Male XLR 3-pin Male XLR 3-pin Male XLR 3-pin
    Power Requirements N/A N/A N/A
    Weight .5 kg (16 oz) .35 kg (11 oz) .4 kg (13 oz)
    Finish Cabernet / Black / Nickel Cabernet / Black / Nickel Cabernet / Black / Nickel

     

  • Avantone CK-1 Small-Capsule FET Pencil Microphone

    Avantone CK-1 Small-Capsule FET Pencil Microphone

    Avantone CK-1 Small-Capsule FET Pencil Microphone

    Avantone CK-1 Small-Capsule FET Pencil Microphone

    The Avantone “Cabernet (C-series)” mics are designed to offer true professional performance. They will meet or surpass the performance and specifications of much higher priced mics. The Avantone CK-1 is truly a gorgeous looking and sounding microphone. The design, character and performance can be compared directly to fine studio-standard FET micsbut at a fraction of their cost!

    Our rugged CK-1 microphone body and capsule assembly are precision machined of brass. Aesthetically, it features an elegant Cabernet Wine-Red finish, accented with polished nickel trim and capsule assembly.

    The CK-1 in its normal stock version uses high grade Polystyrene and Metalized Polypropylene capacitors in the audio path. This represents our commitment to quality as these normally are the type of “upgrade” components that are implemented by microphone modder/hot-rodders!

    The high quality FET circuitry will yield pleasing professional results comparable to much more expensive designs. Any studio can proudly offer the CK-1 for instrumental and percussion mikingIt exudes class visually as well as sonically. The CK-1 is equally at home on the stage for drum overheads, acoustic instruments and piano.

    The CK-1 includes (3) 19mm (3/4″) interchangeable capsules to provide unlimited miking possibilities! Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability. The rugged CK-1 mic is able to produce professional results with a clean sonic character.

    The included SSM Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results. The 3 capsules (cardioid, omni, and Hyper-cardioid) offer versatility for accommodating virtually any miking task.

    The CK-1 has separate -10 dB pad & 80 Hz LF roll off switches….The -10dB attenuation switch can be engaged when miking very high SPL sources to keep from overloading the electronics. The 80Hz high-pass filter switch can be engaged to reduce rumble and to keep unwanted low frequencies from “muddying up” the track.

    Features

    Uses Include
    Cymbals, Hi-Hats, acoustic guitar, drum overheads, piano, percussion etc

    Standard Items Included

    • Avantone CK-1 FET Microphone
    • Avantone SSM Shockmount
    • Elegant padded genuine wooden Mic box
    • 19mm Cardioid, Omni, and Hyper-Cardioid capsules
    • Owners Manual
  • Avantone CK-40 Stereo Multi-Pattern FET Condenser Microphone

    Avantone CK-40 Stereo Multi-Pattern FET Condenser Microphone

     Avantone CK-40 Stereo Multi-Pattern FET MicrophoneAvantone CK-40 Stereo Multi-Pattern FET Microphone

     

    Avantone CK-40 Stereo Multi-Pattern FET Microphone

    The Avantone “Cabernet (C-series)” mics are designed to offer true professional performance. They will meet or surpass the performance and specifications of much higher priced mics. The Avantone CK-40 is truly a gorgeous looking and sounding microphone. The design, character and performance is comparable to some of the world’s finest Stereo FET Mics…but at a fraction of their cost!

    Our rugged CK-40 microphone body and capsule assembly are precision machined of BRASS. Aesthetically, it features an elegant Cabernet Wine-Red finish, accented with polished nickel trim and grill. The Discreet Class A Low-Noise FET circuitry will yield pleasing professional results comparable to much more expensive designs.

    Any studio can proudly offer the stereo CK-40 as a group vocal mic, room mic, piano mic, or utility condenser due to its versatility…It exudes class visually as well as sonically.

    Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability. The versatile Avantone CK-40 Stereo Class A FET microphone features twin LARGE 35mm center-terminated pressure gradient transducers. Their close physical proximity places them in a tight vertical array to allow accurate stereo imaging without phase issues arising. The top capsule/grill assembly rotates UP TO 180 degrees relative to the lower capsule/grill assembly. This feature along with the multi-pattern independent selector choices allow for all stereo recording techniques to be utilized. (XY-Coincident / Blumlein, M-S)

    The 2 sets of pad, pattern select & LF rolloff switches independently control the capsules. (Front switches control the lower fixed grill/capsule while the rear switches control the upper rotating headgrill.) The 3 patterns allow the CK-40 to be used in a variety of situations including M-S recording.

    The -10dB attenuation switch can be engaged when miking very high SPL sources to keep from overloading the electronics.

    The 80Hz HIGH-PASS filter switch can be engaged to reduce rumble and to keep unwanted low frequencies from “muddying up” the track. The CK-40 operates on standard 48 volt phantom power and includes a 5-Pin mic cable that plugs into the included 1×2 stereo splitter box. Two standard XLR mic cables are then all that is required to connect to a phantom powered mic preamp/console channel.

    The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results.

    So many sonic and spatial options are available with this microphone and we encourage you to experiment and use your ears as the final judge for stereo panning spread, use of omni vs cardioid or whether utilizing M-S miking techniques will better serve your particular situation etc…

     

    Features

    Each CK-40 Mic is individually serialized.

    Uses Include:
    Studio group vocals, acoustic guitar, mandolin, drum overheads, piano, room mic, etc…

    Standard Included Items:

    • Avantone CK-40 Stereo FET Microphone
    • Avantone Custom Retro Shockmount W/ Extra Elastic bands
    • 1 x 2 Splitter Box (Stereo Breakout Box)
    • Elegant padded genuine wooden Mic box
    • 30′ 5-pin cable
    • Foam wind filter
    • Padded Aluminum storage / travel case
    • Owners Manual

    Specifications

    Type
    Stereo True Condenser Microphone

    Polar Patterns
    Cardioid, Omni, Figure-8 (x2)

    Capsule(s)
    (2) Dual plate 35mm gold sputtered diaphragm / brass assembly

    Frequency Response
    20-20,000 Hz +/- 3dB

    Output Impedance
    <=250 Ohms / transformer isolated

    Maximum SPL
    147 dB (0.5% THD @1000Hz)

    Equivalent noise level
    17dB (A weighted EC651)

    S/N Ratio
    77dB re 1Pa

    Sensitivity
    -40dB

    Output Connector
    Male XLR 5 pin with included breakout box and cable

    Included Accessories
    -Wood Box
    -Shockmount
    -Foam Filter
    -2×1 splitter box
    -30′ Cable
    -Metal road case

    High-Pass Switch
    80 Hz 6dB/octave

    Attenuation Switch -10dB

    Power Requirements
    Standard 48 Volt Phantom (x2) 3mA current consumption

    Finish
    Polished Nickel trim / Metallic Cabernet Red Body

    Weight
    .95 kgs / 2.1 lbs

    Dimensions
    27.6cm X 49mm

  • Avantone CK-6 Classic Large Diaphragm Cardioid FET Condenser Microphone

    Avantone CK-6 Classic Large Diaphragm Cardioid FET Condenser Microphone

    Avantone CK-6 Classic Large Capsule Cardioid FET Condenser Microphone

    The Avantone “Cabernet (C-series)” mics are designed to offer true professional performance. They will meet or surpass the performance and specifications of much higher priced mics.

    The Avantone CK-6 is truly a gorgeous looking and sounding microphone. The design, character and performance can be compared directly to fine studio-standard FET micsbut at a fraction of their cost! Our rugged CK-6 microphone body and capsule assembly are precision machined of brass.

    Aesthetically, it features an elegant Cabernet Wine-Red finish, accented with polished nickel trim and capsule assembly. The transformerless Discreet Class A FET circuitry will yield pleasing professional results comparable to much more expensive designs. The CK-6 houses a 32mm gold-sputter thin Mylar capsule.

    The CK-6 in its normal stock version uses high grade Polystyrene and Metalized Polypropylene capacitors in the audio path. This represents our commitment to quality as these normally are the type of “upgrade” components that are implemented by microphone modders/hot-rodders! Any studio can proudly offer the CK-6 for instrumental and vocal mikingIt exudes class visually as well as sonically.

    Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability. The versatile CK-6 mic is able to produce professional results with a clean sonic character.

    The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results.

    The CK-6 has separate -10 dB pad & 80 Hz LF roll off switches….The -10dB attenuation switch can be engaged when miking very high SPL sources to keep from overloading the electronics. The 80Hz high-pass filter switch can be engaged to reduce rumble and to keep unwanted low frequencies from “muddying up” the track.

    Features

    Uses Include
    Studio vocals, acoustic guitar, mandolin, drum overheads, piano, etc

    Standard Items Supplied

    • Avantone CK-6 Cardioid FET Microphone
    • Avantone Custom Retro Shockmount
    • Elegant padded genuine wooden Mic box
    • Padded Aluminum storage / travel case
    • Owners Manual

     

    Specifications

    Type
    True Transformerless Condenser

    Polar Pattern(s)
    Cardioid

    Capsule
    Single-sided 32mm center-terminated gold-sputtered Mylar (6 micron)

    Frequency Response
    35-20,000 Hz +/- 3.5dB

    Output Impedance
    <=200 Ohms

    Maximum SPL
    136dB (0.5% THD @1000Hz)

    Equivalent Noise Level
    <17dB

    Output Connector
    Male XLR 3-pin

    High-Pass Switch
    80 Hz 6dB/octave

    Attenuation Switch
    -10 dB

    Power Requirement
    Standard 48 Volt Phantom / 5mA

    Included Accessories
    -Shockmount
    -Wooden Box in Metal Carrying Case

    Dimensions
    155mm x 46mm

    Weight
    .4 kg / .9 lb

    Finish
    Polished Nickel trim / Metallic Cabernet Red Body

  • Avantone CK-7 Large Diaphragm Multi-Pattern FET Condenser Microphone

    Avantone CK-7 Large Diaphragm Multi-Pattern FET Condenser Microphone

    Avantone CK-7 Large Capsule Multi-Pattern FET Condenser Microphone
    Avantone CK-7 Large Capsule Multi-Pattern FET Condenser Microphone

    The Avantone “Cabernet (C-series)” mics are designed to offer true professional performance. They will meet or surpass the performance and specifications of much higher priced mics. The Avantone CK-7 is truly a gorgeous looking and sounding microphone. The design, character and performance can be compared directly to fine studio-standard FET mics…but at a fraction of their cost!

    Our rugged CK-7 microphone body and capsule assembly are precision machined of brass. Aesthetically, it features an elegant Cabernet Wine-Red finish, accented with polished nickel trim and capsule assembly. The transformer coupled Discreet Class A FET circuitry will yield pleasing professional results comparable to much more expensive designs.

    The CK-7 houses a 35mm gold-sputtered thin Mylar capsule. The CK-7 in its normal stock version uses high grade Polystyrene and Metalized Polypropylene capacitors in the audio path. This represents our commitment to quality as these normally are the type of “upgrade” components that are implemented by microphone modders/hot-rodders! Any studio can proudly offer the CK-7 as a vocal mic or utility condenser due to its versatility…It exudes class visually as well as sonically.

    Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability. The versatile CK-7 mic is able to produce professional results with a clean sonic character. The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results. The 3 patterns allow the CK-7 to be used in a variety of situations.

    The cardioid pattern is generally best used on vocals and single instruments. The omni mode works well in incorporating some room sound into the track. The figure 8 pattern allows 2 vocalists to use the mic at the same time from opposite sides. The CK-7 has separate -10 dB pad & 80 Hz LF roll off switches….The -10dB attenuation switch can be engaged when miking very high SPL sources to keep from overloading the electronics. The 80Hz high-pass filter switch can be engaged to reduce rumble and to keep unwanted low frequencies from “muddying up” the track. 

    Features

    Uses Include:
    Studio vocals, acoustic guitar, mandolin, drum overheads, piano, room mic, etc…

    Standard Items Supplied:

    • Avantone CK-7 Multi-Pattern FET Microphone
    • Avantone Custom Retro Shockmount
    • Elegant padded genuine wooden Mic box
    • Padded Aluminum storage / travel case
    • Owners Manual

    Specifications

    Type
    True Condenser

    Polar Pattern(s)
    Cardioid , Omni , Figure 8

    Capsule
    Dual-sided 35mm center-terminated gold-sputter Mylar (6 micron)

    Frequency Response
    20-20,000 Hz +/- 3dB

    Output Impedance
    <=250 Ohms

    Maximum SPL
    139dB (0.5% THD @1000Hz)

    Sensitivity
    -38 dB (0 dB=1V/Pa)

    Equivalent Noise Level
    (A-Weighted per IEC 286-4) < 16 dB

    Output Connector
    Male XLR 3-pin

    High-Pass Switch
    80 Hz 6dB/octave

    Attenuation Switch
    -10 dB

    Power Requirement
    Standard 48 Volt Phantom / 5mA

    Included Accessories 
    -Shockmount
    -Wooden Box in Metal Carrying Case

    Dimensions
    187mm x 51mm / 7.5″ x 2″

    Weight
    .65 kgs / 1.4 lbs

    Finish
    Polished Nickel trim / Metallic Cabernet Red Body

  • Avantone CR-14 Ribbon Microphone

    Avantone CR-14 Ribbon Microphone

     Avantone CR-14 Ribbon MicrophoneAvantone CR-14 Ribbon Microphone

    The Avantone “Cabernet (C-series)” mics are designed to offer true professional performance. They will meet or surpass the performance and specifications of much higher priced mics. The Avantone CR-14 is truly a gorgeous looking and sounding microphone. The design, character and performance is comparable to some of the very finest Ribbon mics…but at a fraction of their cost!

    Our rugged CR-14 microphone body and inner assembly parts are precision machined of brass. Aesthetically, it features an elegant Cabernet Wine-Red finish, accented with polished nickel trim and a black grill. The CR-14 has a unique, “retro” body design.

    The transformer coupled output will yield pleasing professional results comparable to much more expensive designs. Any studio can proudly offer the CR-14 as a guitar cabinet, room mic, drum overheads, vocal mic or utility room mic due to its versatility…It exudes class visually as well as sonically.

    Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability. The versatile CR-14 mic is able to produce professional results with a warm, pleasing sonic character.

    The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results.

    The CR-14’s dual, low-mass ribbon element which enables a much better sensitivity rating than most single ribbon designs. This design lends to fast and accurate transient response, ultra-high 148 dB SPL capability, and overall stunning realism. It has a figure-8 audio directionality (pickup) pattern via front and rear, with extended sweet spots (as compared to Large Diaphragm condenser mics & single ribbon designs).

    The CR-14 has very low residual noise, with no internal active electronics to overload or produce distortion. It also requires no power supply.



    Features

    Uses Include
    Miking guitar amps & cabinets, acoustic guitar, mandolin, drum overheads, vocals, room mic, etc…

    Standard Included Items

    • Avantone CR-14 Ribbon Microphone
    • Avantone Custom Retro Shockmount W/ Extra Elastic bands
    • Elegant padded genuine wooden Mic box
    • Padded Aluminum storage / travel case
    • Owners Manual
     

    Specifications

    Type
    Ribbon Microphone

    Ribbon
    Dual Ribbon / Pure Aluminum / 35mm x 5mm / 2 microns thick

    Polar Pattern
    Figure of 8

    Frequency Response
    30Hz – 15kHz +/- 3dB

    Output Impedance
    <=600 Ohms

    Recommended Load
    Impedance 3000 Ohms

    Maximum SPL
    145dB (0.5% THD @1000Hz)

    S/N Ratio
    70dB re 1Pa

    Sensitivity
    -52 dBv +/- 2dB Re. (0dB=1V/Pa)

    Output Connector
    Male XLR 3 pin

    Included Accessories
    -Padded Wooden Box
    -Shockmount
    -Metal road case

    Power Requirements
    None

    Finish
    Polished Nickel trim / Metallic Cabernet Red Body

    Weight
    16 oz (496 grams)

    Dimensions
    1.45″ (37mm) x 6.89″ (175mm)

     

  • Avantone CV-12 Multi-Pattern Large Diaphragm Tube Condenser Microphone

    Avantone CV-12 Multi-Pattern Large Diaphragm Tube Condenser Microphone

    The Avantone “Cabernet (C-series)” mics are designed to offer true professional performance. They will meet or surpass the performance and specifications of much higher priced mics. The CV-12 is truly a gorgeous looking and sounding microphone. The design, character and performance is comparable to some of the fine vintage tube mics of the 1950’s & 1960’s…but at a fraction of their cost!

    Our rugged CV-12 microphone body and capsule assembly are precision machined of brass. Aesthetically, it features an elegant Cabernet Wine-Red finish, accented with polished nickel trim and grill. The transformer coupled tube circuitry has its origins in famous European vintage designs. Any studio can proudly offer the CV-12 as a primary vocal mic…It exudes class visually as well as sonically. Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability.

    The versatile CV-12 mic is able to produce professional results with a warm, pleasing sonic character. The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results.

    Features

    9-Pattern Tube Microphone w/ dual 32mm gold sputtered thin Mylar capsules

    -10 dB pad  &  80 Hz LF metal roll off toggle switches

    Hand selected Russian made 6072A Tube

    Each CV-12 Mic has a serial number

     

    Uses Include:
    Studio vocals, acoustic guitar, mandolin, drum overheads, room mic, piano

     

    Standard Included Items:

    • Avantone CV-12 Tube Microphone
    • Avantone Custom Retro Shockmount W/ Extra Elastic bands
    • Avantone PS-12 Multi-Pattern Power supply with cables
    • Elegant padded genuine wooden mic box
    • Premium Grade 6072A Tube
    • Padded aluminum storage / travel case
    • Owner’s Manual
  • Avantone CV-28 Small-Diaphragm Tube Condenser Microphone

    Avantone CV-28 Small-Diaphragm Tube Condenser Microphone

    The Avantone “Cabernet (C-series)” mics are designed to offer true professional performance. They will meet or surpass the performance and specifications of much higher priced mics. The Avantone CV-28 is truly a gorgeous looking and sounding microphone. The design, character and performance is comparable to some of the fine vintage tube mics of the 1950’s & 1960’s…but at a fraction of their cost!

    Our rugged CV-28 microphone body and capsule assembly are precision machined of brass. Aesthetically, it features an elegant Cabernet Wine-Red finish, accented with polished nickel trim and grill.

    The transformer coupled tube circuitry offers a modern-day, affordable solution to the desire to capture the character of famous European and American vintage designs. Any studio can proudly offer the CV-28 as a primary acoustic instrument mic…It exudes class visually as well as sonically.

    Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability. The versatile CV-28 mic is able to produce professional results with a warm, pleasing sonic character.

    The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results. 3-Pattern Tube Microphone w/interchangeable 19mm gold sputtered thin Mylar capsule assemblies. Military-grade -15 dB pad & 80 Hz LF roll off switches.

     

    Features

    Uses Include
    Acoustic guitar, mandolin, drum overheads, percussion, piano mic, etc…

    Standard Items Supplied

    • Avantone CV-28 Tube Microphone
    • Avantone Custom Retro Shockmount
    • Avantone PS-28 Proprietary Power supply with cables
    • Elegant padded genuine wooden Mic box
    • 3 Interchangeable 19mm Capsules ( Cardioid, Omni, Hyper-Cardioid)
    • Padded Aluminum storage / travel case
    • Owners Manual

     

    Specifications

    Type
    Tube-type Condenser

    Polar Pattern
    3 patterns via interchangeable capsules (Omni, Cardioid, Hyper-Cardioid)

    Frequency Response
    20-20,000 Hz +/- 3dB

    Output Impedance
    <=250 Ohms / transformer isolated

    Maximum SPL
    136dB (0.5% THD @1000Hz)

    Sensitivity
    20mV/Pa � 34dB

    Equivalent Noise Level
    17dB

    Output Connector
    Male XLR 7 pin w/ special power supply & cables

    Included Accessories
    -Padded Wooden Box
    -Shockmount
    -Metal road case

    Tube Type
    Select Military-Grade 6J1B

    High-Pass Switch
    High-Grade 80 Hz 6dB/octave Switch

    Attenuation Switch
    High-Grade -15dB Switch

    Power Requirement
    Dedicated PS-28 POWER SUPPLY w/switchable 115/230VAC Capability

    Finish
    Polished Nickel trim / Metallic Cabernet Red Body

  • Avantone MONDO Dynamic Kick Drum Microphone

    Avantone MONDO Dynamic Kick Drum Microphone

    Avantone MONDO Dynamic Kick Drum Microphone
    Avantone MONDO Dynamic Kick Drum Microphone

    This is the 2nd generation MONDO kick drum microphone from Avantone and a great deal of R&D effort has culminated in this rugged, great sounding mic. We feel it represents the very finest kick drum microphone available, both for live clubs & concerts, as well as serious studio recording projects.

    The Avantone MONDO kick drum offers a very aggressive frequency contour that sounds huge right out of the box, so most engineers will find little need for EQ.

    Each Avantone MONDO kick drum mic is die cast from zinc, with a brass and steel grill assembly. As with all of our mics, there is NO PLASTIC to break! Aesthetically, each mic features an elegant Cabernet Wine-Red finish, accented with polished nickel trim and a black grill assembly. All components are designed and manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability.

    The Avantone MONDO features internal shockmounting on the capsule assembly to prevent the transmission of unwanted “rumble” from physical vibrations.

    A unique feature of all our drum mics is pair of machined insets on the barrel of the microphone body. These insets allow the O-rings of the SSM shockmount to “lock” the mic into place, which prevents mic shifting and slippage.

    The included SSM shock mount is as rugged as you can find and allows for a superb decoupling of the mics from unwanted low-frequency transfer and rumble. This feature results in a much tighter, less muddy sound than other brands of drum mics. The O-rings are manufactured using a custom formula. The new world class Ethylene Propylene formula provides enormous resistance to breakage, resistance to surface nicks and remains supple and effective even against dry, hot temperatures. It is resistant to ozone and weathering, which makes it great for use around electronics devices, and maintains its physical properties even in a stretched condition. Each SSM is constructed of heavy-duty die-cast zinc, which is not only incredibly durable but also adds mass, which contributes to vibration dampening/decoupling.

    We round out the package with a rugged custom-molded and padded case to safely store and transport your Avantone mic.

    The Avantone MONDO kick drum mic, SSM shockmount, and included carrying case are each inspected, tested, and carefully packed here in New York.

    The Avantone ADM snare drum mic is a truly gorgeous looking and sounding microphone. Its proprietary design, character and performance is made to set a new standard in drum miking. Any studio or venue can proudly & confidently offer the Avantone ADM for professional use during recording or live performance.

     

    Features

    Uses Include
    Kick drums, bass cabinets, large djembes, tympani, large floor toms, etc.

     

    Standard Items Supplied
    -Avantone MONDO kick drum microphone
    -Avantone SSM Shockmount
    -Custom-molded padded carrying case
    -Owners Manual

     

    Specifications

    Type
    Dynamic

    Polar Pattern(s)
    Cardioid

    Frequency Response
    20Hz – 15kHz

    Output Impedance
    210 Ohms

    Maximum SPL
    145dB

    Output Connector
    Male XLR 3-pin

    Power Requirements
    N/A

    Weight
    .5 kg (16 oz)

    Finish
    Cabernet / Black / Nickel

  • Avantone Passive MixCube Pair – Black

    Avantone Passive MixCube Pair – Black

    The Avantone MixCubes are shielded, full-range mini reference monitors.

    Their design is inspired by the legacy from the 5C Sound Cubes utilized in virtually all-major studios for the last Twenty five years.

    Engineering Objective
    To construct a complete range, rugged, mini-reference monitor to replace the older, aging, 5C Sound Cubes that are still being used worldwide, while offering a better, more linear frequency response. A complete year was spent studying all versions & revisions from the famous little 5C Sound Cubes. Research says there have been several driver versions released over the years with widely varying frequency response characteristics. We find the smoothest, most linear, full-range form of those 5C models for our testing benchmark. Next we analyzed their response characteristics in an anechoic chamber and proceeded to implement design upgrades. Realizing the significance of replacing a top “industry-standard reference monitor” we began by replicating its basic size, function, and sonic character.

     

    We desired to take it up a notch though…


    First, we addressed
    your cabinet Design… The initial 5C Sound Cubes were created of ½” particleboard covered with a glue-on wood grain contact paper. We chose to use thicker, denser MDF board because of its high rigidity and inherent low-resonance characteristics. We started having a 165mm (6 1/2″) sealed cube design with radiused edges. We then chose a stylish Polyurethane glossy “RETRO-CREAM” finish. The originals had either screws or on later models plastic binding posts mounted on a recessed plastic cup. We upgraded to high-end nickel plated, machined solid metal binding posts (Dual banana spacing) installed on a black anodized ,milled and silk-screened aluminum terminal plate. Next we added a 7mm thick neoprene pad embedded in to the base of the cabinet for everyone like a skid-resistant acoustic isolator. Additionally, for creative mounting situations, we recessed a business standard 5/8”-27 mic stand mount into the base.

    Second, We addressed the motive force design… The originals were a basic 5” stamped frame design. We designed a proprietary 5.25” die cast aluminum frame driver/cone assembly to exceed the performance of the originals. The mounting bezel will be polished for an elegant appearance. The paper cone, chosen because of its musical character, is custom-designed & crafted using the finest Nz pulp with mica fibers added for lighter weight & rigidity. The material surround is created in Japan to exacting uniform thickness tolerances. The very best Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel enabling the highest modeled flux density within the gap. The magnets are Y- 40 GRADE (MIL-SPEC) yielding a 43oz. High Power-low distortion motor structure.

    Performance Objective
    Studios primarily use 2-way & 3-way larger monitors
    designed to represent a wide range reference viewpoint at higher listening levels. However, within this newly developing age of High Definition Audio, there is still a necessity to also hear what your mix will sound like when played back over small “bass-challenged” systems for example televisions, clock radios, computers, car stereos, iPod docking stations, etc. It is important to make mixing judgments based partially on listening to reference monitors that will not impart tonal anomalies caused by crossovers or inferior full range drivers. Particular attention is definitely paid towards the critical mid-range vocal/guitar/keyboard areas. This is where having a full-range monitor without a crossover is really revealing. Ten months of R&D comparative listening & tweaking went into the voicing from the Avantone MixCubes. The result is a very smooth sounding, full-range upgrade from the original 5C Sound Cubes. Listening tests demonstrate that the MixCubes have a smooth, more open, transparent top end response with extended bass while maintaining their basic original character.

    Amplification & Wiring
    Recommended power rating is 50-200 watts of solid state power or 10-100 watts of tube power. It
    is advisable to use a high quality studio-grade power amplifier. The metal binding posts around the rear of the speaker can accept bare wire, spade lugs, or single or dual banana plugs. It is advisable to use 12 -16 AWG wire for runs more than 6 feet

    Placement
    When positioning the Avantone MixCubes on stands or console bridges
    it is best to keep them at ear level and slightly angled in towards the engineer. Being that they are shielded it is ok to place them near a CRT video monitor or TV without causing any problems. The underside mic stand mounts will even allow you creative positioning options in unusual studio playback situations.


    Avantone MixCubes Passive Mini-Reference Monitor Features

    • 5.25″ Shielded Passive Full range 8 ohm drivers
    • 6 1/2″ Cube Cabinet with multiple coats of “Retro-Cream” High Gloss lacquer finish
    • Precision-milled high-rigidity MDF cabinet sides & baffle for low resonance
    • Radiused corners & edges reduce edge diffraction for better imaging
    • Custom Cone is crafted using New Zealand pulp with mica fibers added for light weight & rigidity
    • Cloth surround made in Japan to uniform thickness tolerances
    • Top Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel
    • The 43oz. low distortion motor structure magnets are Y- 40 GRADE (MIL-SPEC)
    • High-Rigidity DIE-CAST Aluminum frame with polished mounting bezel
    • Nickel Plated “high-end” binding posts (properly spaced for dual banana plugs) – insulated for CE compliance
    • Anodized aluminum milled terminal plate
    • 1/4″ soft Neoprene Pad is recessed into the cabinet base to serve as a non-skid acoustic isolator
    • Standard size (5/8″- 27 threading) female microphone stand mount is built into the cabinet base

     

    Avantone MixCubes Passive Mini-Reference Monitor Specifications

    • System Type: Dynamic Shielded Full-Range Pair
    • Frequency Response: 90Hz – 17,000Hz (useful musical range)
    • Impedance: Nominal 8 ohms
    • SPL / Sensitivity: 93dB @ 1w / 1 meter
    • Recommended Power: From 10-200 watts
    • Driver: 5.25″ cast aluminum frame
    • Cabinet: sealed / 18mm MDF / Dacron acoustical stuffing
    • Inputs: 3-way CE rated plastic encased metal binding posts (accepts up to 12-gauge wire, spade lugs, dual banana plugs)
    • Weight: 6 lbs 11 oz (per speaker)
    • Dimensions: 165mm x 165mm x 165mm (6 1/2″ x 6 1/2″ x 6 1/2″ in)

  • Avantone Passive Mixcube Pair – Butter Cream

    Avantone Passive Mixcube Pair – Butter Cream

    The Avantone MixCubes are shielded, full-range mini reference monitors.

    Their design is inspired by the legacy from the 5C Sound Cubes utilized in virtually all-major studios for the last Twenty five years.

    Engineering Objective
    To construct a complete range, rugged, mini-reference monitor to replace the older, aging, 5C Sound Cubes that are still being used worldwide, while offering a better, more linear frequency response. A complete year was spent studying all versions & revisions from the famous little 5C Sound Cubes. Research says there have been several driver versions released over the years with widely varying frequency response characteristics. We find the smoothest, most linear, full-range form of those 5C models for our testing benchmark. Next we analyzed their response characteristics in an anechoic chamber and proceeded to implement design upgrades. Realizing the significance of replacing a top “industry-standard reference monitor” we began by replicating its basic size, function, and sonic character.

     

    We desired to take it up a notch though…

    First, we addressed your cabinet Design… The initial 5C Sound Cubes were created of ½” particleboard covered with a glue-on wood grain contact paper. We chose to use thicker, denser MDF board because of its high rigidity and inherent low-resonance characteristics. We started having a 165mm (6 1/2″) sealed cube design with radiused edges. We then chose a stylish Polyurethane glossy “RETRO-CREAM” finish. The originals had either screws or on later models plastic binding posts mounted on a recessed plastic cup. We upgraded to high-end nickel plated, machined solid metal binding posts (Dual banana spacing) installed on a black anodized ,milled and silk-screened aluminum terminal plate. Next we added a 7mm thick neoprene pad embedded in to the base of the cabinet for everyone like a skid-resistant acoustic isolator. Additionally, for creative mounting situations, we recessed a business standard 5/8”-27 mic stand mount into the base.

    Second, We addressed the motive force design… The originals were a basic 5” stamped frame design. We designed a proprietary 5.25” die cast aluminum frame driver/cone assembly to exceed the performance of the originals. The mounting bezel will be polished for an elegant appearance. The paper cone, chosen because of its musical character, is custom-designed & crafted using the finest Nz pulp with mica fibers added for lighter weight & rigidity. The material surround is created in Japan to exacting uniform thickness tolerances. The very best Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel enabling the highest modeled flux density within the gap. The magnets are Y- 40 GRADE (MIL-SPEC) yielding a 43oz. High Power-low distortion motor structure.

    Performance Objective
    Studios primarily use 2-way & 3-way larger monitors designed to represent a wide range reference viewpoint at higher listening levels. However, within this newly developing age of High Definition Audio, there is still a necessity to also hear what your mix will sound like when played back over small “bass-challenged” systems for example televisions, clock radios, computers, car stereos, iPod docking stations, etc. It is important to make mixing judgments based partially on listening to reference monitors that will not impart tonal anomalies caused by crossovers or inferior full range drivers. Particular attention is definitely paid towards the critical mid-range vocal/guitar/keyboard areas. This is where having a full-range monitor without a crossover is really revealing. Ten months of R&D comparative listening & tweaking went into the voicing from the Avantone MixCubes. The result is a very smooth sounding, full-range upgrade from the original 5C Sound Cubes. Listening tests demonstrate that the MixCubes have a smooth, more open, transparent top end response with extended bass while maintaining their basic original character.

    Amplification & Wiring
    Recommended power rating is 50-200 watts of solid state power or 10-100 watts of tube power. It is advisable to use a high quality studio-grade power amplifier. The metal binding posts around the rear of the speaker can accept bare wire, spade lugs, or single or dual banana plugs. It is advisable to use 12 -16 AWG wire for runs more than 6 feet

    Placement
    When positioning the Avantone MixCubes on stands or console bridges it is best to keep them at ear level and slightly angled in towards the engineer. Being that they are shielded it is ok to place them near a CRT video monitor or TV without causing any problems. The underside mic stand mounts will even allow you creative positioning options in unusual studio playback situations.

     

    Features

    • 5.25″ Shielded Passive Full range 8 ohm drivers
    • 6 1/2″ Cube Cabinet with multiple coats of “Retro-Cream” High Gloss lacquer finish
    • Precision-milled high-rigidity MDF cabinet sides & baffle for low resonance
    • Radiused corners & edges reduce edge diffraction for better imaging
    • Custom Cone is crafted using New Zealand pulp with mica fibers added for light weight & rigidity
    • Cloth surround made in Japan to uniform thickness tolerances
    • Top Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel
    • The 43oz. low distortion motor structure magnets are Y- 40 GRADE (MIL-SPEC)
    • High-Rigidity DIE-CAST Aluminum frame with polished mounting bezel
    • Nickel Plated “high-end” binding posts (properly spaced for dual banana plugs) – insulated for CE compliance
    • Anodized aluminum milled terminal plate
    • 1/4″ soft Neoprene  Pad is recessed into the cabinet base to serve as a non-skid acoustic isolator
    • Standard size (5/8″- 27 threading) female microphone stand mount is built into the cabinet base
    Specifications:

    System Type
    Dynamic Shielded Full-Range Pair

    Frequency Response
    90Hz – 17,000Hz (useful musical range)

    Impedance
    Nominal 8 ohms

    SPL / Sensitivity
    93dB @ 1w / 1 meter

    Recommended Power
    From 10-200 watts

    Driver
    5.25″ cast aluminum frame

    Cabinet
    sealed / 18mm MDF / Dacron acoustical stuffing

    Inputs
    3-way CE rated plastic encased metal binding posts (accepts up to 12-gauge wire, spade lugs, dual banana plugs)

    Weight
    6 lbs 11 oz (per speaker)

    Dimensions
    165mm x 165mm x 165mm (6 1/2″ x 6 1/2″ x 6 1/2″ in)

     

  • Avantone Pro BV-1 Large-Diaphragm Tube Condenser Microphone

    Avantone Pro BV-1 Large-Diaphragm Tube Condenser Microphone

    The Avantone BV1 is truly a gorgeous looking and sounding microphone. The design, character and performance is comparable to some of the finest vintage tube mics of the 1950’s & 1960’s…but at a fraction of their cost!

    The Avantone Buttercream (B-series) mics are designed to offer premium professional performance. They will meet or surpass the performance and specifications of much higher priced mics. As always, we strive to offer true value at every price point and invite sonic comparisons to higher priced mics.


    Features:

    • Rugged BV1 microphone body and capsule assembly are precision machined of brass.
    • Aesthetically, it features an elegant Retro-Butter-Cream finish, accented with polished nickel trim and grill.
    • The transformer coupled tube circuitry offers a modern-day, affordable solution to the desire to capture the character of famous European and American vintage designs.
    • Rear vents aid in stabilizing internal temperature to help secure tube longevity
    • Any studio can proudly offer the BV1 as a primary Vocal mic…It exudes class visually as well as sonically.
    • Manufactured using premium grade resistors and capacitors along with precision machined brass structural components that yield a very solid feel, superb sonic integrity and rugged reliability.
    • The versatile BV1 mic is able to produce professional results with an open, warm, pleasing sonic character.
    • The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic.
    • 9-Pattern Tube Microphone w/ 34mm gold sputtered thin Mylar capsule assembly
    • -10dB pad & 80 Hz LF roll off switches
    • Uses Include: Vocals, Acoustic guitar, mandolin, drum overheads, percussion, piano mic, etc…

     

    Specifications:

    • Output Impedance: <200 Ohms / transformer isolated
    • Maximum SPL: 134dB (0.5% THD @1000Hz) 144dB with pad engaged
    • Frequency Response: 25Hz-20KHz
    • Equivalent noise level: <18dB (A-weighted IEC 268-4)
    • S/N Ratio: 78dB (Ref. 1Pa A-weighted)
    • Sensitivity: -35dBV
    • Output Connector: Male XLR 7 pin
    • Tube Type: Select Low-Noise Russian 6072A
    • High-Pass Switch: 80 Hz 6dB/octave Switch
    • Attenuation Switch: -10dB Switch
    • Finish: Polished Nickel trim / Glossy Butter-Cream Body
    • Weight (BV-1 Mic Only): 1.3 kgs / 46 oz.
    • Weight (in case): 25 pounds (11.15 kgs)
    • Dimensions (Microphone): 10 x 2.5 inches – 25 x 63 mm – (long x wide)
    • Dimensions of Product Case: 23 x 7.5 x 17 inches

     

    Included Accessories:
     
      –  Power Supply
      –  Padded Wooden Mic Box
      –  Shockmount
      –  Custom Designed Tweed road case
      –  Removable metal pop filter
      –  15’ Gotham GAC-7 Tube Mic Cable
  • Avantone Pro CLA-10A Active Studio Monitor System Pair DEMO unit.

    Avantone Pro CLA-10A Active Studio Monitor System Pair DEMO unit.

    Avantone Pro CLA-10A Active Studio Monitor System Pair DEMO unit.

    The Iconic Studio Monitor System is back.

    Avantone Pro, in conjunction with the expertise of legendary mixer Chris Lord Alge, have designed the most faithful reproduction of the world’s most iconic studio monitor. Now everyone can mix on the monitors that define “the hitmaker sound”. A tremendous amount of design work and exacting detail have finally made the “white cone” monitors available to everyone! And now the world has finally gotten what it always asked for — an active-powered version: the CLA-10A! Black box. White cone. High-range frequency. It’s not known as the world’s best — it’s known for being the world’s best reference — the sound that creates hits.

    The Original Drivers for the Original Sound

    Since the “white cone” studio monitor was discontinued, the supply of aftermarket components have become more and more expensive and less and less available. Avantone Pro has created a near exact recreation of the original drivers. Using our global resources and decade of experience in driver construction, we have reproduced the components faithfully, updating the materials to comply with modern environmental requirements.

     

    The AV10-MHF tweeter dome went through a difficult engineering process to get the exact phenolic resin doping to match the original performance curve. The AV10-MLF woofer uses custom tooled mechanical parts that mirror the original. We worked closely with one of the original vendors of the original cone to get the exact same stiffness and weight. The only difference from the original is that we use a pressed cone as opposed to a lapped. This allows for tighter matching in every cone we build — meaning this is the first time matched pairs have been available!

    Both replacement drivers are physically and dimensionally exactly the same as the originals and are “bolt in” hassle-free installation.

    Available For the First Time in an Active Configuration.

    One of the most common questions asked about the CLA-10A’s is which version of the originals are they based on, and the answer is: all of them! The CLA-10A’s have an all new “VTPC” knob or “Variable Tissue Paper Control.” This VTPC allows you to simulate anything from the Vertical “m” model to the horizontal “Studio” model and everything in between. No more debate over the best tissue paper to use — VTPC has you covered!

    Avantone Pro decided to stay traditional with a linear power supply implementing a massive old school toroidal transformer in order to maintain the legacy sound. The CLA-10A uses a monolithic Class AB amplifier. At low power, THD is a phenomenal 0.005%; at rated load it is 0.1%, yielding excellent performance compared to class D amps. The system yields a rock solid 200WRMS.

     

    Specifications

    • System Type: Active Full-Range Two-Way Stereo Pair
    • System Frequency Response: 60Hz-20,000Hz (Accessible Musical Range)
    • Components: Low Frequency: AV10-MLF 18Cm Cone, High Frequency: AV10-MHF 3.5Cm Soft Dome
    • Cabinet: 10.4 Liter Sealed Design, 18mm MDF With Real Wood Veneer
    • Cabinet Dimensions: 381.5mm X 215mm X197.5mm (15”X 8 ½”X 7- ¾ ”)
    • Weight: 8.2Kg / 18 Lbs (Each)
    • Shipping Weight: 18.5 Kg / 40.5 Lbs
    • SPL: 104dB
    • Peak Musical Output: 110dB (Music Program Material)
    • Amplifier: 200W Class Ab Linear Supply
    • THD: 0.05% At 1Khz, 1W
    • Balanced Inputs: Combination XLR & Phone Jack
    • Unbalanced Input: RCA Phono Jack
    • Volume: +0dB, -120dB
    • VTPC: Variable Tissue Paper Control Fc 1.8Khz +6dB, -30dB.
    • Power: On/off Switch
    • Ground Lift Switch
    • Power: 115Vac/230Vac Selectable
    • Power Consumption:
      • StandBy: 3W
      • Full Output: 250W
  • Avantone Pro CV12 BLA Large-diaphragm Tube Condenser Microphone

    Avantone Pro CV12 BLA Large-diaphragm Tube Condenser Microphone

    Avantone Pro CV12 BLA Large-diaphragm Tube Condenser Microphone

    With a sound that rivals much higher-priced mics, Avantone’s CV12 is renowned for its incredible price-to-performance value. It’s been used in studios worldwide, from modest home setups to top-shelf facilities. And now, thanks to Black Lion Audio, it sounds better than ever. The mod-meisters at BLA have re-engineered this already killer tube mic, giving it a flatter response, balancing its frequency range, sweetening its highs, and maximizing its lows. You also get an upgraded Jetsun shockmount and an eye-catching faux alligator skin case. The Avantone Pro CV12 BLA is one of the best-sounding tube condenser microphones you’ll find in this price range.

    Making a great-sounding mic even better

    Black Lion Audio has been modding gear for over a decade — they know their stuff. For the CV12, they started out with an overhauled circuit that tames the mic’s high-mid bump, resulting in a flatter frequency response. Then they swapped out the existing 32mm K67 capsule for a 34mm CK12-styled, smoothing out the mic’s highs and bringing out its lows. A Solen FastCap coupling capacitor gives you extreme transparency. On top of that, the mic’s power supply has been completely redesigned with a new low-noise circuit, while extra filtering on its transformer bridge diode ensures a super-clean sound. At Sweetwater, we’ve found that the BLA-modded CV12’s improved balanced response and increased headroom sound great on everything. This microphone is a true tube-fueled workhorse.

    About Black Lion Audio

    Founded in Chicago in 2006, Black Lion Audio has made their mark on the audio industry by hot rodding audio equipment and upgrading the sound quality of popular music-production gear, elevating industry-standard products to new levels of sonic quality. Though they started off modding gear from other manufacturers, they’ve utilized their cumulative expertise to design their own line of boutique mic preamps and word clocks. BLA gear and modded gear can be found in studios from LA to New York to Nashville and heard on projects from artists like Maroon 5, Alison Krauss, Metallica, T-Pain, George Strait, MGMT, Beyonce, George Duke, Slayer, Erykah Badu, Rod Stewart, and more.

    Avantone Pro CV12 BLA Features:

    • Overhauled circuit tames the mic’s high-mid bump for a flatter frequency response
    • 34mm CK12-styled capsule smooths out high frequencies and brings out low frequencies
    • Solen FastCap coupling capacitor gives you extreme transparency
    • Redesigned power supply with a new low-noise circuit
    • Extra filtering on its transformer bridge diode ensures a super-clean sound
    • Improved balanced response and increased headroom sound great on everything
    • Jetsun shockmount provides excellent isolation while allowing performers to get closer to the mic
    • Eye-catching faux alligator skin case

    Tech Specs

    • Microphone Type:Tube Condenser
    • Mono/Stereo:Mono
    • Polar Pattern:Multi-pattern, 9 selectable
    • Diaphragm Size:1.33″ (34mm)
    • Frequency Response:20Hz-20kHz (±3dB)
    • Max SPL:136dB SPL (146dB with pad engaged)
    • Output Impedance:250 ohms
    • Signal to Noise Ratio:78dB (A weighted)
    • Sensitivity:-35 dB
    • Low Cut Filter:80Hz
    • Pads:-10dB
    • Tube:6072A
    • Color:Nickel Trim with Metallic Cabernet Red Body
    • Power Source:External Power Supply included
    • Connector:7-pin XLR (mic), XLR (power supply)
    • Dimensions:9.5″ x 1.8″
    • Weight:1.8 lbs.
    • Included Accessories:Jetsun Shockmount, Deluxe Carrying Case
    • Manufacturer Part Number:CV12BLA
  • Avantone Single Passive MixCube – Black

    Avantone Single Passive MixCube – Black

    The Avantone MixCubes are shielded, full-range mini reference monitors.

    Their style is inspired from the legacy in the 5C Sound Cubes used in virtually all-major studios for your last 25 years.

    Engineering Goal
    To build a complete range, rugged, mini-reference monitor to replace the older, aging, 5C Sound Cubes which are nonetheless in use worldwide, while supplying an enhanced, a lot more linear frequency response. A total year was spent studying all versions & revisions of the famous little 5C Sound Cubes. Research says there were several driver versions released over time with widely varying frequency response characteristics. We chose the smoothest, most linear, full-range form of those 5C models to use as our testing benchmark. Next we analyzed their response characteristics in a anechoic chamber and proceeded to employ style upgrades. Realizing the importance of replacing a respected “industry-standard reference monitor” we began by replicating its basic size, function, and sonic character.

    We wanted to go up a notch though…

    First, we addressed the Cabinet Style… The first 5C Sound Cubes were created of ½” particleboard covered with a glue-on wood grain contact paper. We made a decision to use thicker, denser MDF board due to the high rigidity and inherent low-resonance characteristics. We started using a 165mm (6 1/2″) sealed cube style with radiused edges. Then we chose a classy Polyurethane glossy “RETRO-CREAM” finish. The originals had either screws or on later models plastic binding posts mounted on a recessed plastic cup. We upgraded to high-end nickel plated, machined solid metal binding posts (Dual banana spacing) attached to a black anodized ,milled and silk-screened aluminum terminal plate. Next we added a 7mm thick neoprene pad embedded in to the base of the cabinet for everyone as a skid-resistant acoustic isolator. Additionally, for creative mounting situations, we recessed a market standard 5/8”-27 mic stand mount into the base.

    Second, We addressed the motive force design… The originals were a fundamental 5” stamped frame style. We designed a proprietary 5.25” die cast aluminum frame driver/cone assembly to exceed the performance on the originals. The mounting bezel will be polished with an elegant appearance. The paper cone, chosen because of its musical character, is custom-built & crafted using the finest New Zealand pulp with mica fibers added for lighter weight & rigidity. The cloth surround is made in Japan to exacting uniform thickness tolerances. The very best Plate and T-Yoke of driver are constructed with Sumitomo 1008 low carbon steel enabling the highest modeled flux density in the gap. The magnets are Y- 40 GRADE (MIL-SPEC) yielding a 43oz. High Power-low distortion motor structure.

    Performance Objective
    Studios primarily use 2-way & 3-way larger monitors designed to represent a variety reference viewpoint at higher listening levels. However, on this newly developing chronilogical age of Hd Audio, there’s still a necessity to also hear what your mix will seem like when played back over small “bass-challenged” systems including televisions, clock radios, computers, car stereos, iPod docking stations, etc. You should make mixing judgments based partially on playing reference monitors that wont impart tonal anomalies caused by crossovers or inferior full range drivers. Particular attention is usually paid towards the critical mid-range vocal/guitar/keyboard areas. This is when having a full-range monitor without a crossover is really revealing. Ten months of R&D comparative listening & tweaking entered the voicing from the Avantone MixCubes. It makes sense a really smooth sounding, full range upgrade in the original 5C Sound Cubes. Listening tests show the MixCubes use a smooth, more open, transparent top end response with extended bass although maintaining their basic original character.

    Amplification & Wiring
    Recommended power rating is 50-200 watts of solid state power or 10-100 watts of tube power. It is advisable to use a high quality studio-grade power amplifier. The metal binding posts about the rear on the speaker can accept bare wire, spade lugs, or single or dual banana plugs. It is advisable to use 12 -16 AWG wire for runs over 6 feet.

    Placement
    When positioning the Avantone MixCubes on stands or console bridges it’s always best to have them at ear level and slightly angled in on the engineer. Because they are shielded it is ok to put them near a CRT video monitor or TV without causing any problems. The bottom mic stand mounts will also enable you creative positioning options in unusual studio playback situations.

     
     

    Avantone MixCubes Passive Mini-Reference Monitor Features

    • 5.25″ Shielded Passive Full range 8 ohm drivers
    • 6 1/2″ Cube Cabinet with multiple coats of “Retro-Cream” High Gloss lacquer finish
    • Precision-milled high-rigidity MDF cabinet sides & baffle for low resonance
    • Radiused corners & edges reduce edge diffraction for better imaging
    • Custom Cone is crafted using New Zealand pulp with mica fibers added for light weight & rigidity
    • Cloth surround made in Japan to uniform thickness tolerances
    • Top Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel
    • The 43oz. low distortion motor structure magnets are Y- 40 GRADE (MIL-SPEC)
    • High-Rigidity DIE-CAST Aluminum frame with polished mounting bezel
    • Nickel Plated “high-end” binding posts (properly spaced for dual banana plugs) – insulated for CE compliance
    • Anodized aluminum milled terminal plate
    • 1/4″ soft Neoprene Pad is recessed into the cabinet base to serve as a non-skid acoustic isolator
    • Standard size (5/8″- 27 threading) female microphone stand mount is built into the cabinet base

     

    Avantone MixCubes Passive Mini-Reference Monitor Specifications

    • System Type: Dynamic Shielded Full-Range Pair
    • Frequency Response: 90Hz – 17,000Hz (useful musical range)
    • Impedance: Nominal 8 ohms
    • SPL / Sensitivity: 93dB @ 1w / 1 meter
    • Recommended Power: From 10-200 watts
    • Driver: 5.25″ cast aluminum frame
    • Cabinet: sealed / 18mm MDF / Dacron acoustical stuffing
    • Inputs: 3-way CE rated plastic encased metal binding posts (accepts up to 12-gauge wire, spade lugs, dual banana plugs)
    • Weight: 6 lbs 11 oz (per speaker)
    • Dimensions: 165mm x 165mm x 165mm (6 1/2″ x 6 1/2″ x 6 1/2″ in)